Transition Temperature Research Articles

The effect of polycaprolactone polyol molecular weight and chain extender type on the physico-mechanical properties and gas permeability of polyurethane thermoplastic elastomer membranes

ABSTRACT In this study, polyurethane thermoplastic elastomers (TPU) were synthesized using isophorone diisocyanate (IPDI), 1,4-butanediol (BDO), and 1,6-hexanediol (HDO) as the chain extenders, and polycaprolactone diol (PCL-diol) with three different molecular weights (2000, 4000, and 10,000 g/mol) as polyols. Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) patterns, and differential scanning calorimetry (DSC) were conducted to analyze the chemical microstructure and phase morphology of the prepared samples. The results showed that the change in the chain extender’s type (BDO and HDO) leads to a decrease in the hydrogen bonding index (HBI). Increasing the molecular weight of PCL-diol in BDO-based TPUs has led to an increase in their crystallinity, Young’s modulus, melting temperature, tensile strength, and a decrease in glass transition temperature and elongation at break. Moreover, the increase in the molecular weight of PCL-diol in HDO-based TPUs demonstrated an increase in the crystallinity and elongation at break and tensile strength up to the molecular weight 4000 in PCL-diol, after that, there was a decrease in those properties due to the increase of the soft segments content and change in the chain extender type. Permeability on TPU membranes was performed for N2 and CO2 at three different pressures 3, 6, and 9 atm at room temperature. An increase in pressure led to an increase in membrane permeability due to the increase in gas solubility in TPU based on Henry’s law. The permeability of CO2 is higher than N2 due to the proper interactions of CO2 gas with the polar carbonyl groups of polyurethane. It is observed that the permeability increases in BDO-based samples with an increase in the molecular weight of PCL-diol, while the increase in permeability of HDO-based TPU is up to PCL-diol molecular weight 4000 and after that is decreased. The selectivity of CO2 has decreased with increasing pressure due to the higher rate of dissolution of N2 at higher pressures.

Pressure-Dependent Superconductivity in Topological Dirac Semimetal SrCuBi.

The discovery of superconducting states in diverse topological materials generated a burgeoning interest to explore a topological superconductor and to realize a fault-tolerant topological quantum computation. A variety of routes to realize topological superconductors have been proposed and many types of topological materials have been developed. However, a pristine topological material with a natural superconducting state is relatively rare as compared to topological materials with artificially induced superconductivity. Here, we report that the planar honeycomb structured three-dimensional (3D) topological Dirac semimetal (TDS) SrCuBi, which is the Zintl phase, shows a natural surface superconductivity at 2.1 K under ambient pressure. It is clearly identified from theoretical calculations that a topologically non-trivial state exists on the (100) surface. Further, its superconducting transition temperature (Tc) increases by applying pressure, exhibiting a maximal Tc of 4.8 K under 6.2GPa. We believe that this discovery opens up a new possibility of exploring exotic Majorana fermions at the surface of 3D TDS superconductors. This article is protected by copyright. All rights reserved.

Glass transition and crystallization of Se95Te5 chalcogenide glassy semiconductor

The study is dedicated to the investigation of thermo-physical characteristics of Se95Te5 chalcogenide glassy semiconductor during its glass formation and crystallization processes, employing various scanning rates of 5, 10, 15 and 20 K/min in non-isothermal modes through DSC measurement. Analysis of the structural relaxation kinetics involves the Kissinger’s, Augis and Bennett's, as well as Matusita’s approaches. Experimental data yield contains the determination of crucial parameters such as glass transition (𝑇𝑇𝑔𝑔), crystallization(𝑇𝑇𝑐𝑐), and melting temperatures alongside factors like reduced temperature of glass transition (𝑇𝑇𝑟𝑟𝑟𝑟), Hruby’s parameter (𝐾𝐾𝑔𝑔𝑔𝑔), fragility index (𝐹𝐹𝑖𝑖), Avrami exponents (n, m), glass transition (140.24 kJ/mol) and crystallization (Ec = 95.11 kJ/mol) energies, respectively. The results confirm that Se95Te5 chalcogenide system as an efficient glass former. Matusita’s method reveals that the crystallization mechanism (n = 2.51, m = 1.9) corresponds to volumetric nucleation with two-dimensional growth.

Enhancing performance: insights into the augmentation potential of acrylonitrile butadiene styrene/boron nitride composites

Abstract This work aims to investigate the morphological, mechanical and thermal characteristics of boron nitride (BN)-reinforced acrylonitrile-butadiene styrene (ABS) composites. ABS and ABS/BN composites with a maximum BN loading up to 8 wt% were developed using two-roll mill followed by compression molding. Scanning electron microscopy (SEM) images presented interlinking of BN flakes in the dimple texture of ABS. A modest decrease in tensile properties was observed for the composites. The tensile strength and impact strength for the ABS/BN8 specimen were lowered by 4.7 and 81.7 %, respectively. On the other hand, hardness increased by 3.39 % for ABS/BN8 composite. The interaction effect of BN in the ABS matrix on the thermal properties was assessed using thermo-gravimetric analysis (TGA). An enhancement in the thermal-stability was observed for BN incorporated ABS. There is a modest shift in glass transition (T g) temperature to a higher value for the ABS/BN composites.

Observation of Hydrostatic‐Pressure‐Modulated Giant Caloric Effect and Electronic Topological Transition

AbstractPhase transition is a fundamental phenomenon in condensed matter physics, in which states of matter transform to each other with various critical behaviors under different conditions. The magnetic martensitic transformation features significant multi‐caloric effects that benefit the solid‐state cooling or heat pumping. Meanwhile, the electronic topological transition (ETT) driven by pressure has been rarely reported in martensitic systems. Here, the modulation effects of hydrostatic pressure on phase transitions in a magnetic martensitic alloy are reported. Owing to the huge volume expansion during the transition, the martensitic transition temperature is driven from 339 to 273 K by pressure within 1 GPa, resulting in highly tunable giant baro‐ and magneto‐caloric effects (BCE and MCE) in a wide working temperature range. Interestingly, an ETT is further induced by pressure in the martensite phase, with a sudden drop of the measured saturation magnetization around 0.6 GPa. First‐principles calculations reveal a sharp change in the density of states (DOS) due to the orbit shift around the Fermi level at the same pressure and reproduce the experimental observation of magnetization. Besides, the ETT is accompanied by remarkable changes in the lattice parameters and the unit‐cell orthorhombicity. The study provides insight into pressure‐modulated exotic phase‐transition phenomena in magnetic martensitic systems.

Dome structure in pressure dependence of superconducting transition temperature for HgBa2Ca2Cu3O8 : Studies by ab initio low-energy effective Hamiltonian

The superconducting (SC) cuprate HgBa2Ca2Cu3O8 (Hg1223) has the highest SC transition temperature Tc among cuprates at ambient pressure Pamb, namely, Tcopt≃138 K experimentally at the optimal hole doping concentration. Tcopt further increases under pressure P and reaches 164 K at optimal pressure Popt≃30 GPa, then Tcopt decreases with increasing P>Popt generating a dome structure [Gao , ]. This nontrivial and nonmonotonic P dependence of Tcopt calls for a theoretical understanding and mechanism. To answer this open question, we consider the low-energy effective Hamiltonian (LEH) for the antibonding (AB) Cu3dx2−y2/O2pσ band derived generally for the cuprates. In the AB LEH for cuprates with Nℓ≤2 laminated CuO2 planes between block layers, it was proposed that Tcopt is determined by a universal scaling Tcopt≃0.16|t1|FSC [Schmid , ], where t1 is the nearest-neighbor hopping, and the SC order parameter at optimal hole doping FSC mainly depends on the ratio u=U/|t1| where U is the onsite effective Coulomb repulsion: The u dependence of FSC has a peak at uopt≃8.5 and a steep decrease with decreasing u in the region u<uopt irrespective of materials dependent on other parameters. In this paper, we show that |t1| increases with P, whereas u decreases with P in the Hamiltonian of Hg1223. Based on these facts, we show that the domelike P dependence of Tcopt can emerge at least qualitatively if we assume Hg1223 with Nℓ=3 follows the same universal scaling for Tcopt, and Hg1223 is located at the slightly strong coupling region u≳uopt at Pamb and u≃uopt at Popt by taking account of expected corrections to our calculation. The consequence of these assumptions is the following: With increasing P within the range P<Popt, the increase in Tcopt is accounted for by the increase in |t1|, whereas FSC is insensitive to the decrease in u around ≃uopt and hence to P as well. At P>Popt, the decrease in Tcopt is accounted for by the decrease in u below uopt, which causes a rapid decrease in FSC dominating over the increase in |t1|. We further argue the appropriateness of these assumptions based on the insight from studies on other cuprate compounds in the literature. In addition, we discuss the dependencies of u and |t1| on each crystal parameter (CP), which provides hints for design of even higher Tcopt materials. Published by the American Physical Society 2024

The Butterfly Effect: Multifaceted Consequences of Sensitizer Concentration Change in Phase Transition-based Luminescent Thermometer of LiYO2:Er3+,Yb3.

In response to the ongoing quest for new, highly sensitive upconverting luminescent thermometers, this article introduces, for the first time, upconverting luminescent thermometers based on thermally induced structured phase transitions. As demonstrated, the transition from the low-temperature monoclinic to the high-temperature tetragonal structures of LiYO2:Yb3+,Er3+ induces multifaceted modification in the spectroscopic properties of the examined material, influencing the spectral positions of luminescence bands, energy gap values between thermally coupled energy levels, and the red-to-green emission intensities ratio. Moreover, as illustrated, both the color of the emitted light and the phase transition temperature (from 265 K, for LiYO2:Er3+, 1%Yb3+, to 180 K, for 10%Yb3+), and consequently, the thermometric parameters of the luminescent thermometer can be modulated by the concentration of Yb3+ sensitizer ions. Establishing a correlation between the phase transition temperature and the mismatch of ion radii between the host material and dopant ions allows for smooth adjustment of the thermometric performance of such a thermometer following specific application requirements. Three different thermometric approaches were investigated using thermally coupled levels (SR = 1.8%/K at 180 K for 1%Yb3+), green to red emission intensities ratio (SR = 1.5%/K at 305 K for 2%Yb3+), and single band ratiometric approach (SR = 2.5%/K at 240 K for 10%Yb3+). The thermally induced structural phase transition in LiYO2:Er3+,Yb3+ has enabled the development of multiple upconverting luminescent thermometers. This innovative approach opens avenues for advancing the field of luminescence thermometry, offering enhanced relative thermal sensitivity and adaptability for various applications.

Low-Temperature Nanosecond Laser Process of HZO-IGZO FeFETs toward Monolithic 3D System on Chip Integration.

Ferroelectric field-effect transistors (FeFETs) are increasingly important for in-memory computing and monolithic 3D (M3D) integration in system-on-chip (SoC) applications. However, the high-temperature processing required by most ferroelectric memories can lead to thermal damage to the underlying device layers, which poses significant physical limitations for 3D integration processes. To solve this problem, the study proposes using a nanosecond pulsed laser for selective annealing of hafnia-based FeFETs, enabling precise control of heat penetration depth within thin films. Sufficient thermal energy is delivered to the IGZO oxide channel and HZO ferroelectric gate oxide without causing thermal damage to the bottom layer, which has a low transition temperature (<250 °C). Using optimized laser conditions, a fast response time (<1 µs) and excellent stability (cycle >106, retention >106 s) are achieved in the ferroelectric HZO film. The resulting FeFET exhibited a wide memory window (>1.7V) with a high on/off ratio (>105). In addition, moderate ferroelectric properties (2·Pr of 14.7 µCcm-2) and pattern recognition rate-based linearity (potentiation: 1.13, depression: 1.6) are obtained. These results demonstrate compatibility in HZO FeFETs by specific laser annealing control and thin-film layer design for various structures (3D integrated, flexible) with neuromorphic applications.

Insensitivity of Tc to the residual resistivity in high-Tc cuprates and the tale of two domes

One of the few undisputed facts about hole-doped high-Tc cuprates is that their superconducting gap Δ has d-wave symmetry. According to ‘dirty’ d-wave BCS theory, even structural (non-magnetic) disorder can suppress Δ, the transition temperature Tc and the superfluid density ρs. The degree to which the latter is affected by disorder depends on the nature of the scattering. By contrast, Tc is only sensitive to the total elastic scattering rate (as estimated from the residual resistivity ρ0) and should follow the Abrikosov-Gor’kov pair-breaking formula. Here, we report a remarkable robustness of Tc in a set of Bi2201 single crystals to large variations in ρ0. We also survey an extended body of data, both recent and historical, on the LSCO family which challenge key predictions from dirty d-wave theory. We discuss the possible causes of these discrepancies, and argue that either we do not understand the nature of disorder in cuprates, or that the dirty d-wave scenario is not an appropriate framework. Finally, we present an alternative (non-BCS) scenario that may account for the fact that the superconducting dome in Tl2201 extends beyond that seen in Bi2201 and LSCO and suggest ways to test the validity of such a scenario.

Performance of bioresorbable peptide incorporated polymers produced for fused deposition modelling (FDM)

The use of biomaterials in additive manufacturing (AM) of medical devices has gained significant attention over the years, especially in areas such as wound care and orthopedics. This study aims to investigate the performance of bioresorbable peptide-incorporated polymers produced for fused deposition modelling (FDM) process. Herein, we report FDM 3D Printing process of bioactive polymers comprising polycaprolactone (PCL), poly(lactic-co-glycolic acid) (PLGA) or polylactic acid (PLA) or blended with peptide–containing brush copolymers bearing similar synthetic polymer side chains. Mechanical, thermal and rheological properties of the materials were carried out and we report that the incorporation of bioactive polymers into these biodegradable polymers does not result in significant changes to glass transition temperature, melt temperature, tensile properties of the base polymers. However, it was observed that flexural and rheological properties altered significantly. This study provides an insight into the thermomechanical performance of bioresorbable peptide-incorporated polymers for FDM utilization which allows for their use potential in medical device fabrication.

Evaluation of Viscoelastic Performance and Molecular Structures of Natural Rubber/NBR Blends Reinforced by Carbon Black and Nano-Silica

This study focuses on the evaluation of the dynamic mechanical properties, molecular structure, density, hardness, swelling behavior of natural rubber blends (NR) and nitrile rubber (NBR) reinforced with carbon black and/or nano-silica. An experimental work has been conducted to study of the effects of increasing NR content and incorporating nano-silica on the mechanical properties and molecular structure were studied using dynamic mechanical analysis (DMA) and Fourier transform infrared (FTIR) spectroscopy. The results show that increasing the NR content and/or incorporating nano-silica into the elastomer leads to a higher storage modulus with no significant change in the glass transition temperature. FTIR analysis indicates the compatibility of the polyblends and the presence of oxidation of the main polymer chain generated during the grinding of the rubber. Additionally, the results of the swelling study demonstrate that stronger molecular interactions occur on the surface of the nano-silica between the nitrile radicals in the NBR and the silanol (Si-OH) radicals. These findings suggest that blending NR and NBR with carbon black and/or nano-silica can improve the mechanical properties and compatibility of the resulting polyblends, with potential applications in the development of advanced elastomeric materials.

(Thermo)mechanical and chemical characteristics of photochemically crosslinked acrylates from bio‐ and fossil‐based origin

AbstractThe acrylates with oligomers and monomers from (partially) bio‐based feedstock become available at (semi‐)industrial scale, which can be processed through photochemical crosslinking for applications in coatings, additive manufacturing, electronics, or inks. Although fossil‐ and bio‐based acrylates may have a similar chemical composition, it requires good understanding of processing and structure–property relationships as minor changes in microstructure may strongly alter the performance. A comparative study on mechanical properties and chemical structure of bio‐ and fossil‐based acrylates with different functionalities and backbone structures reveals higher ductility of bio‐based acrylates, in relation with a more complex organization of the intrinsic molecular structure. The latter is confirmed by mechanical testing and visco‐elastic characteristics (dynamic mechanical analysis) yielding lower stiffness and higher dampening of bio‐based acrylates, in parallel with a lower glass transition temperature (differential scanning calorimetry). The complex molecular arrangements include a nanoscale morphology with ordered structure (X‐ray diffraction), conformational changes (infrared spectroscopy), and a residual high‐molecular weight fraction (size exclusion chromatography). The visco‐elastic calculations indicate only 4% to 5% lower crosslinking density and around 10% higher mean molar mass of the polymer chains segments between chemical crosslinks and trapped chain entanglements, which explain the unique structure and performance of bio‐based acrylates.

Mechanical recycling of poly(lactic acid)/agave fiber biocomposites

This paper focuses on evaluating the mechanical recycling potential of poly(lactic acid) (PLA) biocomposites reinforced with agave fibers (AF). The biocomposites were prepared by extrusion using 5, 15, and 30 wt.% of agave fibers and reprocessed up to eight times. The results show that the fiber dimensions substantially decrease during reprocessing, especially after the first extrusion cycle, followed by a more gradual decrease in each subsequent cycle. The melt flow index (MFI) and the mechanical properties (except impact strength) tend to decrease as the fiber concentration increases. On the other hand, the glass transition temperature ( T g) and the crystallinity ( X c) of the biocomposites increased with increasing fiber concentration. It is important to highlight that closed-loop reprocessing does not significantly affect the overall behavior of the biocomposites under the conditions investigated. Therefore, PLA reinforced with AF is suitable for primary recycling since the final properties are mainly influenced by the fiber concentration and less by the number of reprocessing cycles.

Molecular Simulation of Covalent Adaptable Networks and Vitrimers: A Review

Covalent adaptable networks and vitrimers are novel polymers with dynamic reversible bond exchange reactions for crosslinks, enabling them to modulate their properties between those of thermoplastics and thermosets. They have been gathering interest as materials for their recycling and self-healing properties. In this review, we discuss different molecular simulation efforts that have been used over the last decade to investigate and understand the nanoscale and molecular behaviors of covalent adaptable networks and vitrimers. In particular, molecular dynamics, Monte Carlo, and a hybrid of molecular dynamics and Monte Carlo approaches have been used to model the dynamic bond exchange reaction, which is the main mechanism of interest since it controls both the mechanical and rheological behaviors. The molecular simulation techniques presented yield sufficient results to investigate the structure and dynamics as well as the mechanical and rheological responses of such dynamic networks. The benefits of each method have been highlighted. The use of other tools such as theoretical models and machine learning has been included. We noticed, amongst the most prominent results, that stress relaxes as the bond exchange reaction happens, and that at temperatures higher than the glass transition temperature, the self-healing properties are better since more bond BERs are observed. The lifetime of dynamic covalent crosslinks follows, at moderate to high temperatures, an Arrhenius-like temperature dependence. We note the modeling of certain properties like the melt viscosity with glass transition temperature and the topology freezing transition temperature according to a behavior ruled by either the Williams–Landel–Ferry equation or the Arrhenius equation. Discrepancies between the behavior in dissociative and associative covalent adaptable networks are discussed. We conclude by stating which material parameters and atomistic factors, at the nanoscale, have not yet been taken into account and are lacking in the current literature.

Multiscale Transfer Printing via Shape Memory Polymer with High Adhesion and Modulus Switchability.

Flexible electronics have gained significant attention as an innovative solution to meet the growing need for information collection from the human body and the environment. However, a critical challenge lies in the need for a transfer printing technique that can fabricate rigid and brittle devices on flexible organic substrates. Here, we develop a multiscale transfer printing technique using an ultraviolet-curable shape memory polymer (SMP) that serves as both the stamp and the receiver substrate. The SMP demonstrates exceptional mechanical performance with toughness at room temperature and remarkable flexibility near its glass transition temperature. The SMP material exhibits an impressive shape recovery ratio and remarkable adhesion switchability. We demonstrate robust transfer printing of diverse objects with different materials and morphologies and in situ transfer of multiscale metallic structures. In addition, the in situ fabricated transparent hyperthermia patches with embedded metal grids are demonstrated, offering potential application in the field of sensors, wearable devices, and electronic skin.

Comparison of Sucrose and Trehalose for Protein Stabilization Using Differential Scanning Calorimetry.

The disaccharide trehalose is generally acknowledged as a superior stabilizer of proteins and other biomolecules in aqueous environments. Despite many theories aiming to explain this, the stabilization mechanism is still far from being fully understood. This study compares the stabilizing properties of trehalose with those of the structurally similar disaccharide sucrose. The stability has been evaluated for the two proteins, lysozyme and myoglobin, at both low and high temperatures by determining the glass transition temperature, Tg, and the denaturation temperature, Tden. The results show that the sucrose-containing samples exhibit higher Tden than the corresponding trehalose-containing samples, particularly at low water contents. The better stabilizing effect of sucrose at high temperatures may be explained by the fact that sucrose, to a greater extent, binds directly to the protein surface compared to trehalose. Both sugars show Tden elevation with an increasing sugar-to-protein ratio, which allows for a more complete sugar shell around the protein molecules. Finally, no synergistic effects were found by combining trehalose and sucrose. Conclusively, the exact mechanism of protein stabilization may vary with the temperature, as influenced by temperature-dependent interactions between the protein, sugar, and water. This variability can make trehalose to a superior stabilizer under some conditions and sucrose under others.

Synthesis, Crystal Structure, and Optical and Magnetic Properties of the New Quaternary Erbium Telluride EuErCuTe3: Experiment and Calculation

This paper reports for the first time on a new layered magnetic heterometallic erbium telluride EuErCuTe3. Single crystals of the compound were obtained from the elements at 1120 K using CsI as a flux. The crystal structure of EuErCuTe3 was solved in the space group Cmcm (a = 4.3086(3) Å, b = 14.3093(9) Å, and c = 11.1957(7) Å) with the KZrCuS3 structure type. In the orthorhombic structure of erbium telluride, distorted octahedra ([ErTe6]9−) form two-dimensional layers (Er(Te1)2/2e(Te2)4/2k−∞2), while distorted tetrahedra ([CuTe4]7−) form one-dimensionally connected substructures (Cu(Te1)2/2e(Te2)2/1t5−∞1) along the [100] direction. The distorted octahedra and tetrahedra form parallel two-dimensional layers (CuErTe32−∞2) between which Eu2+ ions are located in a trigonal-prismatic coordination environment (EuTe610−). The trigonal prisms are connected by faces, forming chains (Eu(Te1)2/2(Te2)4/22−∞1) along the [100] direction. Regularities in the variations in structural parameters were established in the series of erbium chalcogenides (EuErCuCh3 (Ch = S, Se, and Te)) and tellurides (EuLnCuTe3 (Ln = Gd, Er, and Lu)). Ab-initio calculations of the crystal structure, phonon spectrum, and elastic properties of the compound EuErCuTe3 were performed. The types and wavenumbers of fundamental modes were determined, and the involvement of ions in the IR and Raman modes was assessed. The experimental Raman spectra were interpreted. The telluride EuErCuTe3 at temperatures below 4.2 K was ferrimagnetic, as were the sulfide and selenide derivatives (EuErCuCh3 (Ch = S and Se)). Its experimental magnetic characteristics were close to the calculated ones. The decrease in the magnetic phase transition temperature in the series of the erbium chalcogenides was discovered.

Theoretical investigation of (La4O6)n, (La2Ce2O7)n, and (Ce4O8)n nanoclusters (n = 10, 18): Temperature effects and O-vacancy formation.

We report a theoretical investigation of temperature, size, and composition effects on the structural, energetic, and electronic properties of the (La4O6)n, (La2Ce2O7)n, and (Ce4O8)n nanoclusters (NCs) for n = 10, 18. Furthermore, we investigated the single O vacancy formation energy as a function of the geometric location within the NC. Our calculations are based on the combination of force-field molecular dynamics (MD) simulations and density functional theory calculations. We identified a phase transition from disordered to ordered structures for all NCs via MD simulations and structural analysis, e.g., radius changes, radial distribution function, common neighbor analysis, etc. The transition is sharp for La36Ce36O126, La20Ce20O70, and Ce72O144 due to the crystalline domains in the core and less abrupt for Ce40O80, La40O60, and La72O108. As expected, radius changes are abrupt at the transition temperature, as are morphological differences between NCs located below and above the transition temperature. We found a strong dependence on the O vacancy formation energy (Evac) and its location within the NCs. For example, for La40O60, Evac decreases almost linearly as the distance from the geometric center increases; however, the same trend was not observed for Ce40O80, while there are large deviations from the linear trend for La20Ce20O70. Evac has smaller values for Ce40O80 and higher values for La40O60, that is, almost three times, while Evac has intermediate values for mixed oxides, as expected from weighted averages. Therefore, the mixture of one formula unit of La2O3 with two formula units of CeO2 has the effect of increasing the stability of CeO2 (binding energy), which increases the magnitude of the formation energy of the O vacancy.

Synergistic Effect of PBz/Epoxy/PCLA Composite Films with Improved Thermal Properties

Polybenzoxazines (PBzs) are advanced forms of phenolic resins that possess many attractive properties, including thermally induced self-curing polymerization, which produces void-free polymer products without any by-product formation. They also possess a high Tg (glass transition temperature) and thermal stability, but the produced materials are brittle in nature, due to which the final form of their application is very difficult. Hence, in this paper, an attempt has been made to overcome the brittleness of PBz by blending it with epoxy and ε-caprolactam (CPLA) to produce free-standing PBz/Epoxy/PCLA (polycaprolactam) films. The curing process between the three components (i.e., Bzo, epoxy, and caprolactam) was monitored using differential scanning calorimetric (DSC) analysis. The results show that there is no appreciable shift in curing the exotherm observed, except a slight shift in the curing process. However, the heat liberated during the exotherm (ΔH) decreases drastically from 121 to 84 J/g, indicating that the content of benzoxazine is very important as it is involved in the polymerization process through oxazine ring-opening. The morphological studies analyzed using SEM and AFM analyses indicate that there was no observable phase separation up to 30 wt.% of CPLA loading, whereas a higher CPLA content of 50 wt.% causes agglomeration and leads to distinctive phase separation. Moreover, the thermal stability of the composite film, PBz/Epoxy/PCLA30, is also increased with a 10% degradation temperature, T10, of 438 °C, when compared with an PBz/Epoxy film. From the obtained results, it is evident that the formation of a composite film through the melt blending process could produce a tough and thermally stable film without sacrificing individual properties.

Glucose-stabilized polyvinyl acetate homopolymer-based wood adhesive: synthesis and characterization

The purpose of this work was to study the synthesis and characterization of an adhesive based on a glucose stabilized polyvinyl acetate homopolymer. Vinyl acetate monomer was stabilised onto liquid glucose using emulsion polymerization, and polymerization happened using potassium persulfate as an initiator. Here, the effects of adding liquid glucose as a stabiliser for adhesives were studied. Therefore, the current research examines whether liquid glucose, introduced at weight-based concentrations of 0.5% and 1.0%, is suitable as a colloid to produce PVAc adhesives for wood. By measuring viscosity, pH, contact angle, differential scanning calorimetry (DSC), and the pencil hardness test of films, the effect of adding liquid glucose as a colloid on physical, thermal, and mechanical properties was investigated. The shear strength of the PVAc homopolymers applied to wood using emulsions with varied liquid glucose concentrations was measured using a universal tensile machine. As the concentration of liquid glucose increased, the viscosity of the adhesives also considerably increased. Water resistance significantly rose when liquid glucose content increased, as was found by measuring the water contact angle. The use of liquid glucose increased the hardness of PVAc films, which was supported by the glass transition temperature. According to EN 204-205, the tensile shear strength with 1.0% of liquid glucose increased by 63.88% and 45.67%, respectively, over a pristine sample after 6 h of bonding in a dry environment and 24 h in a wet environment. The study’s overall conclusion highlights the higher adhesion capability of PVAc emulsion-based adhesives stabilized by liquid glucose.